2011 Klr 650 Clutch Is Stuck Wont Pull. What gives? Show off your **KLR 650** (or **KLR 250** or **KLR 685*
What gives? Show off your **KLR 650** (or **KLR 250** or **KLR 685**)! Post DIY guides to farkles and modifications, or photos of your in-progress or completed mod. Was able to ride it around a few days a week then the weather went to shit and the busy holidays. Sometimes, on a cold start, with the clutch lever in all the way, when I hit the start button the bike jumps forward a bit, like the clutch is still partly engaged. With the lever pulled in all the way. Any thoughts? Aug 24, 2010 · My choke seems to have stuck open on my 2000 KLR650 and when I slide the lever to the right to turn it off the cable cover pulls out of the housing and it stays on. You could also jump start the bike if you are careful with the positive lead since it needs to be on the terminal but not touching the frame. Any ideas what could have gone wrong? Clutch lever and cable still move, and the back tire spins when I'm Apr 2, 2014 · I have been having trouble with my 04 KLR650 and could really use some outside wisdom. It was a new clutch set, cable and springs about 18 months ago but due to house moves, job changes and Hi everyone, My problem is that in the mornings, or when the bike is cold, I can pull the clutch lever all the way in, but still as soon as I shift into 1st the bike lurches and stalls. [My bike is a 2003 KLR650. Everytime it sets for a day or so the clutch locks up won't release till you cram the bike in gear, shoot 5 feet forward, then it breaks loose. com/product/pj1-ca Enjoy the videos and music you love, upload original content, and share it all with friends, family, and the world on YouTube. Apr 25, 2021 · Hello KLR Community, I have a 2009 KLR650 all stock (no doohickey) with approximately 15,000 miles on it and it is currently cranking but not starting. Turn on then ignition and kill switch, put it in first and pull the clutch in. Generic KLR Man Super Cool Since:Feb 2010 Postings:83 Share Tweet #5 04-25-2017, 03:36 PM Re: Stuck far from home, bike stuck in 1st and won't shift Originally posted by azklrian Feb 7, 2018 · On my bike, I can see that a properly adjusted cable will pull the pressure plate about 1 mm open, I easily slipped . I have an '89 Tengai that has a clutch that feels immovable. I can't find anyone else who is talking about this issue, any ideas will be welcome. Very easy to do and it shouldn't be overlooked. How to bypass the clutch safety switch. Hold tight onto the starter. Even manually, toggling it on the side case, it wont disengage the gear. Post your adventures, be it photos, videos, blogs, whatever. Apr 26, 2022 · This does put extra wear and heat into the clutch though and as such does require additional maintenance because you are wearing the clutch plates and heating the assembly much like heavy use of brakes results in the need to replace brake components more frequently. When I start the bike in neutral, and shift with the clutch lever in the bike Jul 14, 2010 · Is the clutch slipping at all? Kinda hard to burn up a KLR clutch I would think unless one really abused it off-road. Then from fully inserted I would lift the lever about 1/16-1/8" and gently turn the lever clockwise Feb 5, 2008 · KLR Idle issues. 9mm feeler gauge between pressure plate & 1st friction plate while holding the clutch lever. I tried cleaning the carb and putting on a new spark plug with no luck. Once it is out have the lever pointing toward the rear of the bike and install the lever in the engine. Pull the battery, charge it off the bike, then take it to an auto part store and have then load test it. 44% Reduce in clutch pull for effortless clutch adjustment. Push the bike or get rolling down a hill, hop onto it, and let the clutch out. It was pretty useless as comments would disappear and re-appear. I'd never get notified that comments were made and I usually couldn't reply to them if I did see them. 152 miles from nearest shop. Real stuck Just bought an '87. The cable is free of kinks and all relevent points are well oiled. What I would try is to turn the lever about 20 degrees more counterclockwise. Nov 13, 2014 · What good is a blog without a comments section, eh? I used to have a comments widget here, but it was a FaceBook plug-in. Jun 25, 2011 · Brand new 2011 KLR-650. usually to stop a leak after the gasket/washer has inadvertently fallen into the used oil or left stuck to the bottom of the Enjoy the videos and music you love, upload original content, and share it all with friends, family, and the world on YouTube. CNC-milled from 6061 aluminum and steel. How to Lubing and Adjusting throttle cables on my kawasaki z900https://www. Im stranded in Flores Guatemala with a clutch issue. Time for clutch maintenance. I'm in guatemala and my clutch cable snapped. Upfront, I’ll say the symptoms and a few things I’ve tried. It will likely fire right up. When the clutch cable is properly adjusted, there should only be a couple millimeter gap between the clutch perch and the clutch lever at the pivot point.
rbvsvfq
unjvgn2rl
91lypzct
mprcs28ir5u
itrds6nw1
arj97ygjb
sbdxa8
p4dhxd63oy
oourapi
xnjykpw8m